![]() ![]() Either give as a gift or give to the kids to play with. Test the flashlight in a dark room to see if the projection is correct.Ħ. (Optional: If you are using a flashlight with a curved glass - to keep from distorting, attach the card stock to a cut coffee cup and attach that to the end of the flashlight)ĥ. Attach the card stock to the end of the flashlight. If you are using black card stock, also use a Christmas-themed scrapbook paper to punch out and put on the top (this is really just for aesthetics – the card stock will be doing all of the work. Using your craft punch stamp, stamp different shapes into the cardstock within the circle that you drew for your flashlight (keep in mind that every flashlight will vary in size).ģ. You can do this with a ruler, or just trace the flashlight onto the paper.Ģ. Measure the circumference of the lighted end of your flashlight. You should now be able close the second half of the tray, to keep the slide in place.DIY Flashlight Projectors - Home & Familyġ. The metal pen I used didn't seem to suffer any ill affects. I had to fix a plastic pen's hole so my multi-color twist pen would work smoothly again. Align the slide's holes with the tabs, now one by one push the pen over the slide holes and onto the alignment tabs. Find a pen that is able to fit over the alignment tabs. Using a retractable pen became the solution. Later I used a drill bit, with a brad point, and turned that in place with my hands (the drill caused more harm than good, but turning the bit by hand worked very well).īetween the holes not being perfect and the plastic being less forgiving (than the paper), the slides needed some additional help to seat into the trays. For a few I used a sharp knife, and turned the point to cut a hole. The paper clip method didn't work through the plastic transparency. With the paper tests, I was able to poke thru the paper with a paper clip. I need to cut matching holes in the slides so they can fit over those tabs (which I marked in red on my template). My projector slide trays have three alignment tabs. Link to the template I created Step 2: Design New Custom Slides Using the Template Glue the LED lights in between the bowls. Glue the paper bowls to the cover of the lightbox to make clouds. This easy-to-make lighting fixture can take on any hue or shade, depending on the colored material you choose. If you're using the same slide projector as I am, you can skip this step and just use the template I've already created. This DIY cloud light, which you can make in the afternoon, will add a touch of magic to your home. Otherwise the new slides kind of bunched up a little when inserted into the trays. Note: later I found the plastic transparency was less forgiving than the paper test prints, and needed to trim the sides slightly. I duplicated the object many times so that I could fill an entire 8 1/2" x 11" page with them. And a separate layer for the images I'll add in the next step.An invisible/printable layer (all black to make sure the background is black).I have a visible/printable layer for part of the template.With the dimensions correct I grouped parts of the object and assigned it to a layer. ![]() I used a paper clip to make holes in the printed paper tests to fit over those alignment tabs.Īfter many test prints and tweaks to the dimensions, I finalized the template. So a little extra work now, may save you time later. but, they help align the slide into the tray. I supposed you could snap those off, to make the process easier. Pay attention to any protrusions, like the three raised parts. You'll want the same shape so the slide will fit inside the tray. I then recreated it as a template in Visio. I used a digital caliber to check the dimensions of the slide. The version I'm using has two little plastic tabs that need to be pried open. ![]() I'm used to using Microsoft Visio, but any SVG editor should work just as well. 1st step was determining the size of the slides inside the trays, and making a template. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |